Cisco 200-105 Cisco Certified Network Associate Routing & Switching certification exam as a profession has an extraordinary evolution over the last few years. Cisco Certified Network Associate Routing & Switching 200-105 exam is the forerunner in validating credentials against. Here are updated Cisco 200-105 exam questions, which will help you to test the quality features of DumpsSchool exam preparation material completely free. You can purchase the full product once you are satisfied with the product.

♥ MARCH 2018 200-105 Exam Questions ♥

200-105 exam questions, 200-105 PDF dumps; 200-105 exam dumps (249 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest Cisco 200-105 Dumps Exam Questions and Answers:

Version: 9.0
Question: 21

Which statement about MPLS is true?

A. It operates in Layer 1.
B. It operates between Layer 2 and Layer 3.
C. It operates in Layer 3.
D. it operates in Layer 2.

Answer: B

MPLS belongs to the family of packet-switched networks. MPLS operates at a layer that is generally considered to lie between traditional definitions of OSI Layer 2 (data link layer) and Layer 3 (network layer), and thus is often referred to as a layer 2.5 protocol.

Question: 22

Which statement about named ACLs is true?

A. They support standard and extended ACLs.
B. They are used to filter usernames and passwords for Telnet and SSH.
C. They are used to filter Layer 7 traffic.
D. They support standard ACLs only.
E. They are used to rate limit traffic destined to targeted networks.

Answer: A

Question: 23

Which statement about the IP SLAs ICMP Echo operation is true?

A. The frequency of the operation .s specified in milliseconds.
B. It is used to identify the best source interface from which to send traffic.
C. It is configured in enable mode.
D. It is used to determine the frequency of ICMP packets.

Answer: D

This module describes how to configure an IP Service Level Agreements (SLAs) Internet Control Message Protocol (ICMP) Echo operation to monitor end-to-end response time between a Cisco router and devices using IPv4 or IPv6. ICMP Echo is useful for troubleshooting network connectivity issues. This module also demonstrates how the results of the ICMP Echo operation can be displayed and analyzed to determine how the network IP connections are performing.
ICMP Echo Operation
The ICMP Echo operation measures the end-to-end response time between a Cisco router and any devices using IP. Response time is computed by measuring the time taken between sending an ICMP Echo request message to the destination and receiving an ICMP Echo reply.
In the figure below ping is used by the ICMP Echo operation to measure the response time between the source IP SLAs device and the destination IP device. Many customers use IP SLAs ICMP-based operations, in-house ping testing, or ping-based dedicated probes for response time measurements.
Figure 1. ICMP Echo Operation

The IP SLAs ICMP Echo operation conforms to the same IETF specifications for ICMP ping testing and the two methods result in the same response times.
Configuring a Basic ICMP Echo Operation on the Source Device
1. enable
2. configure terminal
3. ip sla operation-number
4. icmp-echo {destination-ip-address | destination-hostname} [source-ip {ip-address | hostname} | source-interface interface-name]
5. frequency seconds
6. end

Question: 24

Which type of interface can negotiate an IP address for a PPPoE client?

A. Ethernet
B. dialer
C. serial
D. Frame Relay

Answer: B

Question: 25

Which option is a benefit of switch stacking?

A. It provides redundancy with no impact on resource usage.
B. It simplifies adding and removing hosts.
C. It supports better performance of high-needs applications.
D. It provides higher port density with better resource usage.

Answer: D

A stackable switch is a network switch that is fully functional operating standalone but which can also be set up to operate together with one or more other network switches, with this group of switches showing the characteristics of a single switch but having the port capacity of the sum of the combined switches.

Question: 26

What is the first step you perform to configure an SNMPv3 user?

A. Configure server traps.
B. Configure the server group.
C. Configure the server host.
D. Configure the remote engine ID.

Answer: B

New Updated 200-105 Exam Questions 200-105 PDF dumps 200-105 practice exam dumps:


Facebook Comments